Home Default
NC-Technology Bending-Stamping-Assembly-Tool on Bihler BM 4500

NC-Technology Bending-Stamping-Assembly-Tool on Bihler BM 4500

Bihler BM 4500 / 300 ppm

A-Side: production of housing, plus spring assembly into the housing.

B-Side: production of housing

Assembling 3 -variant plastic housings in transport chain, assembling two wires plus release lever in plastic housing, then assembling stamped parts in plastic housing, labeling plastic housing, pushing it into blister machine.

BIHLER BM 4500
A-Side / 1-out at 300 ppm
D&C StampTec Comfort-Standard-Cutting-Bending-Assembly-Design Punch and bend housing from the right, pull in spring from the left, spring mounted in housing.
BIHLER BM 4500
A-Side / 1-out at 300 ppm
D&C StampTec Comfort-Standard-Cutting-Bending-Assembly-Design Punch and bend housing from the right, pull in spring from the left, spring mounted in housing.
BIHLER BM 4500
A-Side / 1-out at 300 ppm
D&C StampTec Comfort-Standard-Cutting-Bending-Assembly-Design Punch and bend housing from the right, pull in spring from the left, spring mounted in housing.
BIHLER BM 4500
A-Side / 1-out at 300 ppm
D&C StampTec Comfort-Standard-Cutting-Bending-Assembly-Design Punch and bend housing from the right, pull in spring from the left, spring mounted in housing.
BIHLER BM 4500
B-Side / 1-out at 300ppm
D&C StampTec Comfort-Cutting-Bending-Design, punch and bend spring from left side, spring strip moves around the machine for further processing on the A-side
BIHLER BM 4500
B-Side / 1-out at 300ppm
D&C StampTec Comfort-Cutting-Bending-Design, punch and bend spring from left side, spring strip moves around the machine for further processing on the A-side
BIHLER BM 4500
B-Side / 1-out at 300ppm
D&C StampTec Comfort-Cutting-Bending-Design, punch and bend spring from left side, spring strip moves around the machine for further processing on the A-side
BIHLER BM 4500
B-Side / 1-out at 300ppm
D&C StampTec Comfort-Cutting-Bending-Design, punch and bend spring from left side, spring strip moves around the machine for further processing on the A-side
BIHLER BM 4500
Assembly by use of a transport chain / 2-out at 150 strokes p.m.
Three variants of plastic parts are fed in two lanes and mounted in chain. Wire is fed in two lanes, cut off and mounted in plastic part. Release levers are fed in two lanes, cut off and mounted in plastic part.
BIHLER BM 4500
Assembly by use of a transport chain / 2-out at 150 strokes p.m.
Three variants of plastic parts are fed in two lanes and mounted in chain. Wire is fed in two lanes, cut off and mounted in plastic part. Release levers are fed in two lanes, cut off and mounted in plastic part.
BIHLER BM 4500
Assembly by use of a transport chain / 2-out at 150 strokes p.m.
Three variants of plastic parts are fed in two lanes and mounted in chain. Wire is fed in two lanes, cut off and mounted in plastic part. Release levers are fed in two lanes, cut off and mounted in plastic part.
BIHLER BM 4500
Assembly by use of a transport chain / 2-out at 150 strokes p.m. Assembling stamped parts mounted in plastic housing by a turntable. 100% inspection by means of camera monitoring for good/bad part separation. Labeling plastic housing, Pushing plastic housing into blister machine.
BIHLER BM 4500
Assembly by use of a transport chain / 2-out at 150 strokes p.m. Assembling stamped parts mounted in plastic housing by a turntable. 100% inspection by means of camera monitoring for good/bad part separation. Labeling plastic housing, Pushing plastic housing into blister machine.
BIHLER BM 4500
Assembly by use of a transport chain / 2-out at 150 strokes p.m. Assembling stamped parts mounted in plastic housing by a turntable. 100% inspection by means of camera monitoring for good/bad part separation. Labeling plastic housing, Pushing plastic housing into blister machine.
BIHLER BM 4500
Assembly by use of a transport chain / 2-out at 150 strokes p.m. Assembling stamped parts mounted in plastic housing by a turntable. 100% inspection by means of camera monitoring for good/bad part separation. Labeling plastic housing, Pushing plastic housing into blister machine.

Monstroid’s second Generation.

Bihler stamping bending assembly tools

Bihler GRM-NC Leantool-Linear

Bihler GRM-NC

Bihler GRM-NC, 2-out / 140 strokes pm

Extremely sophisticated Leantool linear die with D&C StampTec solutions, 2-fold production using two tracks in a row.

Bihler Stamping-Bending-Tool on GRM 80P

Bihler Stamping-Bending-Tool on GRM 80P

Bihler GRM 80P / 140 ppm

Extremely challenging Stamping-Bending-Part with multi 180° bends, large pitch and accordingly long bending tool.

Final Products

D&C StampTec - final products

Final Products

Contact us
Contact us